MEO Class 4B Exam Questions and Answer of MEP

In this
post we have given the list of the questions that were asked in oral examinations
of 4B. In this post I have picked some of the famous questions that were asked
in the Marine engineering practice oral exams. Answer to these will be published
shortly. If you have any suggestions, please drop a reply below. 

Oral Question Bank for MEO Class 4B Examinations

FUNCTION 6: Marine engineering practice
     
      1. Explain how will you o’haul a fuel injector
      2. Explain how you will change gland packing of a pump.
      3. What is a SDNR valve?
      4. How do you o’haul a globe valve?
      5. How does a gate valve work?
      6. If a gate valve is stuck, what could be the reason?
      7. How is a job centered on a chuck in a lathe
      8. What safety precautions will you take if working on a lathe?
      9. What is a reamer? Where is it used?
      10. How does a Quick closing valve work?
      11. How do you reset a QC valve after operation?
      12. Is there any difference between relief valve and safety valve?
      13. Explain how will you prepare for Bunkering?
      14. How do you set tappet clearance?
      15. What are the steps to take after a blackout at sea?
      16. How do you pressure test a fuel vale?
      17. How will you replace an exhaust valve seat?
      18. How do you install a bearing on a shaft?
      19. How do you specify pipe size?
      20. What do the numbers on bearings mean?
      21. What is the common size between different schedules of a pipe?
      22. If an A/E does not start what will be your action?
      23. Your action if T/C is surging?

You might be interested in reading this: All you need to know about being 4th Engineer


      24. Why is a Steam trap used in condensate return lines?
      25. How is gas cutting done?
      26. How many valves are there on a gas-cutting torch?
      27. How do you light a gas-cutting torch and adjust the flame?
      28. How do you set up a new pipe for welding?
      29. What is GPR/GPO/LH electrodes?
      30. How do you select the correct current setting for welding?
      31. Crank pin bearing clearance
      32. Telescopic feeler gauge
      33. Piston removal procedure
      34. Welding defects?
      35. Bridge gauge main brg clearance
      36. How does a Stud extractor work?
      37. How does a chain block work?
      38. What are the safeties on cargo cranes ?
      39. What are the safeties on ER crane?
      40. How is the load controlled during lowering?
      41. How is the E/R crane load tested?
      42. Fuel valve not coming out?
      43. Setting exhaust valve timing
      44. Pumps o’haul?
      45. Type of drill bits?
      46. Types of threads?
      47. Pipe schedule?
      48. Important dimensions of flanges? Types of flanges?
      49. Indications of scavenge fire? What action will you take?
      50. Where are wear rings used? What is their purpose?
……………………………………………………………………………………………………………………………………………….
      51. Boiler gauge glass? Reflex type? Blow through procedure?
      52. .ISSA code book?
      53. SG hunting gear?
      54. Axe blade? How fitted?
      55. Load test?
      56. SCBA pressure testing
      57. Welding surface preparation
      58. No water in GG ? What action
      59. Flaring tool
      60. What is an ermato joint?
      61. Why is a copper gasket annealed ?
      62. How will you supervise a lub oil Filter cleaning?
      63. What precautions have to be taken during cleaning of SW line filters?
      64. What is a Dead mans alarm
      65. What will be your action if your Reliever appears drunk
      66. Your oiler appears drunk. What is your action?
      67. Compound gauge?
      68. Method of blowing through gauge glass
      69. Pump shaft broken? Suggest epairs?
      70. What is Gear Back lash?
      71. What are different types of gears seen in ship?
      72. What is hunting tooth
      73. Why is gear oil different others?
      74. What are the different types of Taps and Dies?
      75. Why do you take Ullages? How do you calculate liquid quantity?
      76. What is VRF?
      77. What do you check up while opening piston?
      78. Q closing valve operation? Why do you shut the valve again before
      opening?
      79. Start airline getting hot – what action?
      80. Draw a LS of ball bearing fitted on a shaft.
      81. What is a lip seal? Sketch
      82. Sketch a mechanical seal.
      83. Exhaust bellow sketch?
      84. What is a dresser coupling
      85. What is Bumping Clearance? How do you measure it?
      86. Why is a centrifugal pump started with its discharge valve shut?
      87. How will you align a pump to its motor?
      88. What checks will you make on a bottom end bearing bolt?
      89. How do you measure ovality of a crank pin?
      90. How does hydraulic tightening work?
      91. Why is the jack turned back a little while slackening?
      92. What will you check in UP space inspection?
      93. How will you do crankcase inspection?
      94. Shipside valve is leaking into E/R. What will you do?

Hope you liked my article.

You Might Like to Read These Posts Too:

Mark Eriscson

Love to write about topics related to maritime sector. Was born in sailor's family, so love to ride on those high seas. In free time i would like to go for a good sunbath and some soothing guitar music. Want to have my own boat one day.

One thought on “MEO Class 4B Exam Questions and Answer of MEP

  • November 10, 2016 at 11:23 am
    Permalink

    It is very much helpfull!!…..
    From where i can get meo class 4th written examination queations..??

    Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

Special Topics For You

Read these

College Of Maritime Studies and Research- COMSAR College Of Maritime Studies and Research also called as COMSAR in short, is a institute in Kolkata which offers Engine Simulator Courses for Class 4...
Best Books for Studying Marine Engineering Topic W... Marine Engineering is that branch of technical education that covers, mostly the technical aspects of marine machinery. It includes marine engines, ...
Ship Safety and Environment Protection Question Ba... In this post I have discussed questions that are asked in the Class 4B exam of MMD. This is the part 15 of series dealing with th...
Naval Architecture Terminology and Coefficients of... The ship is defined in terms of its size and the shape. This is required to find out it’s characteristics for stability, resistance, power needed to...
Marine engineering knowledge previous year questio... In this post we have discussed the questions that were asked in the Class 4b MMD exam. This is the part 5 of series dealing with ...
Marine Engineering Practice Questions and Answers-... Find the answers to the questions related to troubleshooting of various machineries onboard like hydrophore system, and they come in Marine Engineer...
MEO Class 4B Motor Function Oral Questions-Part 1 Get to know about the questions that are asked in the meo class 4b oral exam of motor function. This function is also called as 4B function. The ful...
Centrifugal Purifiers or Separators Theory, Workin... Learn about centrifugal purifiers working, theory related to their working and about the new ALCAP principal that is used nowadays. Purifiers are on...
error: Content is protected !!