Different types of Boiler Mountings, their purpose and Functions

Boiler is an important piece of instrument that is being used on ship. It is used to generate steam and in turn this steam is used for various purposes like heating of fuel oil, laundry etc. Since Boiler is a pressurized vessel and it is needed all the time, proper function of this piece of equipment is always necessary. There are various mountings fitted on the sides of boiler, so that it can work properly and that too in a controlled manner. Boiler working is a nice topic a to read and pdf boiler books are available in plenty  In this article I have discussed about every mounting and discussed them in proper detail.

Boiler Mountings and their functions

Safety Valves- They are two in number but can be three also, if the boiler has an super heater fitted inside it. This is a very important mountings fitted on the boiler and its proper function is prerequisite. If it is not maintained properly, its working is abysmally affected. Safety valve protects boiler from an uneven increase in pressure. It entails to be set up on a desired value that is safe enough and when pressure in boiler reaches to that level, it lifts up and releases the pressure developing inside the boiler. It is always set at a pressure which is 3% more than the boiler working pressure.
Main Steam Stop valve- This valve regulates the flow of steam to the distribution lines from boiler. It is slowly opened, so as to avoid any type of water hammering taking place in the distributing lines and damaging them. It is a Screw down non return valve and do not allow steam to come to the boiler back. Adjacent to it an auxiliary steam stop valve is also installed and it is used in case main Steam stop valve is damaged due any reason and making unfit for further use.
Feed Check Valve- Fresh water from hot well tank is supplied to the boiler with the help of these valves. These are also SDNR (Screw down non return valve) type of valve and have a flow that can only go in one direction. It avoids pressurized water inside the boiler to come out and damage the pump, pumping the fresh water.
 Boiler Mountings
Water gauges- This piece of equipment is used to measure the level of water inside the boiler. It is very important to keep an eye on the level of water inside the boiler, because if it goes below the normal level, then it can affect boiler working.  There are two water level gauges provided in every boiler and one works as a standby type.
Pressure Gauges- To measure the pressure of steam that is being developed inside the boiler, pressure gauges are used. But they are not directly connected to boiler and reason behind this is that, direct steam can damage this piece of instrument. So, a coil which cools down the steam to low levels is used before this pressure gauge.
Salinometer Cocks- These cocks are used to for taking samples of boiler water for taking readings related to the presence of chemical inside the boiler. A cooling coil is also fitted for the high pressure boilers.
Blowdown Valve- This valve is used for purging the boiler. By purging we mean that, in course of time at the bottom of boiler various types of impurities like corrosion deposits, chemical starts accumulating. So, it becomes necessary to remove theses sediments and hence this process is called as the purging.
Scum Valve- Sometimes with feed water, some oil particles come inside the boiler. Now these oil particles starts floating at the top of the water level and this sometimes cause less heat transfer to water. A valve called as Scum is used in order to remove these oily particles and get rid of this problem creating stuff.

You Might Like to Read These Posts Too:

Mark Eriscson

Love to write about topics related to maritime sector. Was born in sailor's family, so love to ride on those high seas. In free time i would like to go for a good sunbath and some soothing guitar music. Want to have my own boat one day.

Leave a Reply

Your email address will not be published. Required fields are marked *

Special Topics For You

Read these

Black Out on Ship, Recovery and Actions to be take... Black Out on Ship is a common term which is used, when she loses all the power due to the failure of generators. Well  the reason of happening such...
Fresh Water Generator Working and Overhauling For any mariner ‘fresh water generator’ is the most simple but most important machine on board. It uses the sea water and by evaporation it gives us t...
Construction and Working Principal of Incinerator One can absolutely say that the incinerator is like a boiler and the only difference is that in this machinery we do not generate the steam. Cons...
Naval Architecture Terminology and Coefficients of... The ship is defined in terms of its size and the shape. This is required to find out it’s characteristics for stability, resistance, power needed to...
Two Term and Three Term Boiler Water Level Control... This article discusses about how the water level of boiler is kept under control. Two terms and three terms are the controllers that are used in the b...
How to Start and Stop Fresh Water Generator Fresh water generator as name suggest is an machinery onboard which is used to generate fresh water for various purposes like drinking, washing etc....
What is Shipboard Ventilation, and Low and High Ve... In this article you will get to know about the shipboard ventilation system used on ship. Furthermore, the two system namely: high and low veloci...
What is Single and Twin Duct System in Air Conditi... This article discusses about the Single duct and twin duct system used on the ship to distribute the conditioned air. As we know...
error: Content is protected !!